Easily check your error code

Samsung · Washer

Samsung Washer LC Error Code: Water Leak or Water Level Problem

Also shown as: LC1, LE, LE1, 1C, 1E, 1 LC, 1 1C, 11E

LC

LC (LE on older models) means your Samsung washer detected water where it shouldn't be or a water-level problem. The usual causes are a small leak, a drain hose set too low, or too many suds. Check those first. If none of them fit, Samsung recommends service.

Easy⏱ 15–45 minUpdated 2026-11-18

What LC means

Samsung groups LC, LC1, LE and LE1 with the water-level codes 1C and 1E. Samsung US describes them together as a water level or leakage error: moisture is detected somewhere it doesn't belong, or the sensor itself has a problem. Samsung UK calls LC/LE "low water level detected" and 1C/1E a water level sensor issue. Samsung Australia lists them all as leaking errors. In practice, look for a leak first, then check the drain hose height and suds, and only then suspect the sensor.

Likely causes (most → least common)

  1. A small leak from a hose, connection or door sealMost common

    Samsung US says leaks are often so small they go unnoticed, and fixing the leak fixes the code. Check both ends of the supply and drain hoses, the rubber washers in the hose ends, and (on front-loaders) the door seal, where even one strand of hair can let water through.

  2. Drain hose too low or pushed too deep (siphoning)Very common

    Samsung UK asks you to check that the drain hose is not lower than the base of the washer. Samsung US specifies the hose should go 6–8 inches into the standpipe without an airtight seal. Deeper than that, it siphons water out. Water draining away by itself makes the washer think the level is wrong.

  3. Drain hose holder screw removedCommon after a move

    Samsung US warns that removing the clamp holding the drain hose to the back of the washer can make it drain on its own and show an LC or 4C code. Put the holder back with any screw that fits. If the holder is missing, request service.

  4. Too much detergent or non-HE detergentCommon

    Excess suds can be misread by the level sensing. Samsung US suggests running an empty cycle without additives. If suds appear, keep running empty cycles until they stop.

  5. Water level sensor or internal leakLess common

    If there are no suds, no visible leak and the hose is correct, Samsung recommends service.

How to fix it, step by step

  1. Let the washer finish draining

    Samsung Australia notes that some models drain automatically for up to 3 minutes when this code appears, with the Power button disabled. Wait until draining stops before you look for leaks.

    Easy⏱ 3 min🔧 No tools
  2. Look for a leak

    Switch off at the wall. Check the floor under and behind the washer, both ends of each hose and the rubber washers inside the hose ends. On front-loaders, fold back the door seal and check it for hair, threads or tears. Samsung US notes that a few drips from a front-loader door right after opening are normal.

    Easy⏱ 10 min🔧 Flashlight, Towel
  3. Check the drain hose position

    The hose end must not sit lower than the base of the washer (Samsung UK). In the US, Samsung specifies 6–8 inches into the standpipe, no airtight seal, and a height of 18–96 inches (24–35 inches if it drains into a sink). Straighten any kinks. Do not remove the screw and holder that fix the hose to the back of the washer.

    Easy⏱ 10 min🔧 Tape measure, Zip tie
  4. Rule out suds

    Run an empty rinse or short cycle with no detergent or softener. If suds appear, too much or non-HE detergent was used. Repeat empty cycles until no suds remain, then use less HE detergent.

    Easy⏱ 20–40 min🔧 No tools
  5. Power-reset

    Samsung UK's advice for 1C/1E and LC is to switch the washer off at the mains for 1 minute, switch it back on and start a new programme.

    Easy⏱ 2 min🔧 No tools
  6. Request service if it returns

    If there is no leak, no suds and the hose is correct, but the code keeps coming back, the sensor or an internal part needs a technician.

    Easy⏱ —🔧 No tools

When to call a professional

  • Water is coming from inside the cabinet or from under the drum, not from a hose or the door.
  • The door seal is torn or the drain hose is damaged.
  • The drain hose holder at the back is missing. Samsung says this needs service.
  • No leak, no suds and a correctly fitted hose, but the code keeps coming back.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Inlet hose washers / replacement supply hose

A worn rubber washer or cracked hose is a common source of small leaks.

Fit: Hose fittings differ between regions and models. Compare with your old hose before buying.

No price shown — prices are only listed when verified on a retailer page.

Door seal (boot gasket)

Only if the seal is torn. Replacement is a moderate-to-hard job.

Fit: Model-specific for front-loaders.

No price shown — prices are only listed when verified on a retailer page.

Drain hose holder / clamp

If the holder that fixes the drain hose to the back is missing.

Fit: Model-specific. Samsung advises requesting service if it is missing.

No price shown — prices are only listed when verified on a retailer page.

Related codes

More Samsung washer codes

Same problem on other brands

All Samsung washer error codes · Every code A–Z

FAQ

Is LC the same as LE on a Samsung washer?

Yes. Samsung lists LC, LC1, LE and LE1 together. Newer displays show C and older ones show E.

Is 1C the same problem as LC?

They are closely related. Samsung US puts 1C/1E and LC/LE in one water level or leakage group. Samsung UK lists 1C/1E separately as a water level sensor issue, with a 1-minute power reset as the fix. The checks on this page cover both.

Why does my washer keep draining when it shows LC?

Some models drain automatically for a few minutes to protect your floor when they detect a leak or wrong water level. Samsung Australia mentions up to 3 minutes. Wait for it to finish.

Can too much detergent cause an LC code?

Samsung US includes an empty test cycle to check for suds as part of LC troubleshooting. If suds appear, the detergent amount or type was the problem.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.