Samsung · Washer
Samsung Washer HC Error Code: Water Temperature or Heater Problem
Also shown as: HE, H1, Hr, 1 HC, HC2, HE1
HC (HE on older models) on a Samsung washer is a water-temperature or heating error. Samsung UK and Australia first point to the supply hose: hot water reaching the cold inlet, or swapped hoses. If the hoses are right, a reset may clear it, and if the code returns Samsung treats it as a heater fault for service.
What HC means
HC is one of the codes where Samsung's regional pages differ. Samsung UK lists H1/HC/HE as a water temperature issue: the hose should be connected to the cold supply, not the hot one. Samsung Australia lists HC/HE both under water temperature errors (hoses swapped or the cold hose loose) and under temperature sensor errors. Samsung US lists HC, HE, HE1 and Hr as a heater error, with a power reset and then service. Samsung UK also lists HE1 on its own as "water heater not functioning", which needs service. So: check the hoses first, reset second, and call service if the code returns.
Likely causes (most → least common)
- Hot water reaching the cold inlet (single-fill models)Most common on cold-fill models
Samsung UK's fix for HC/HE is to check that the hose is connected to the cold supply, usually the blue tap.
- Hot and cold hoses swapped (dual-inlet models)Common after installation or a move
Samsung Australia asks you to check that the red hose goes to the hot tap and the blue hose to the cold tap, and that the cold hose is tightened securely.
- Temporary sensor readingOccasional
Samsung Australia's temperature-sensor advice and Samsung US's general advice are the same: power off for 2–3 minutes, then restart the cycle.
- Heater, heater circuit or temperature sensor faultLess common
If the hoses are right and the code returns after a reset, Samsung US lists HC/HE as a heater error, and Samsung UK lists HE1 as a heater not working. Both are service jobs.
How to fix it, step by step
Check the supply hose connections
Close the taps and follow each hose from the washer to the wall. On a single-inlet (cold-fill) washer the hose must go to the cold tap. On a dual-inlet washer, hot goes to hot (red) and cold to cold (blue). Swap any hoses that are the wrong way round, re-tighten the cold hose, and open both taps fully.
Check the cold water really is cold
Run the cold tap for a few seconds. If it comes out warm, the problem may be in the home plumbing, for example a mixed or swapped supply under the sink. A plumber can fix that, not a washer technician.
Power off for 2–3 minutes
Switch the washer off at the wall, wait 2–3 minutes, switch it on and restart the cycle.
Test with a warm cycle
Run a short warm cycle and watch whether the code returns during the heating phase. Note at which point it appears. That helps the technician.
Request service if it returns
If the hoses are correct and HC/HE comes back, Samsung treats it as a heater or temperature-sensor fault. HE1 in particular is listed by Samsung UK as a heater that isn't working. Book service. The heater sits inside the tub behind the panels.
When to call a professional
- The code returns after the hoses are confirmed correct and the washer has been power-cycled.
- Your display shows HE1 (Samsung UK: water heater not functioning) or HE3 (steam function).
- Washes are coming out cold, or the breaker or RCD trips during heating.
- Any repair that means opening the cabinet to reach the heater or sensor.
Parts that may be involved
Always match the part to your exact model number (rating label) before ordering.
Inlet hoses (hot/cold)
Only if a hose is damaged while you are swapping or re-tightening it.
Fit: Check your region's thread standard and the length you need.
No price shown — prices are only listed when verified on a retailer page.
Heating element (model-specific)
Only if a technician confirms the heater has failed.
Fit: Match the model number.
No price shown — prices are only listed when verified on a retailer page.
Water temperature sensor (thermistor)
If diagnosed as faulty.
Fit: Model-specific.
No price shown — prices are only listed when verified on a retailer page.
Related codes
More Samsung washer codes
FAQ
Is HC the same as HE on a Samsung washer?
Yes, they are listed together (newer displays use C, older ones E). HE1 is listed separately by Samsung UK as a heater that isn't working.
Why does Samsung say HC is a hose problem in one country and a heater problem in another?
Samsung's regional pages describe the code differently: the UK page as a water temperature (hose) issue, the US page as a heater error, and the Australian page under both. Fix the free cause first by checking the hoses, then reset, and book service if it returns.
Can I still use the washer with an HC code?
A cold wash may still work, but the code will probably come back on heated cycles. If the hoses are right, get it checked rather than running it repeatedly.
What is the difference between HC and 4C2?
Samsung uses 4C2/4E2/nF1 specifically for very hot water in the cold supply (swapped hoses). HC/HE covers water temperature or heating more broadly. Both start with the same hose check.
Sources
This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.
- What do the codes on my washing machine mean? — Samsung UK (last checked 2026-11-18)
- Samsung Washing Machine Error Codes — Samsung Australia (last checked 2026-11-18)
- Samsung washing machine information and error codes — Samsung US (last checked 2026-11-18)