Easily check your error code

Samsung · Dishwasher

Samsung Dishwasher OC Error Code: Too Much Water (Over-Level) — Causes & Fixes

Also shown as: 0C, OE, oE

OC

OC (also shown as 0C or oE) means your Samsung dishwasher detected more water inside than it should hold. It is usually a drain or foam problem — a clogged filter, kinked drain hose or the wrong detergent — not a broken part.

Easy⏱ 20–60 minUpdated 2026-11-19

What OC means

Samsung calls OC an over-level water error: the water level in the tub is higher than the machine expects. Samsung groups it with the 5C drain error, because water that cannot leave the tub (or foam that lifts the level) is the usual reason. Samsung UK describes the typical symptoms as the cycle stopping part-way, small puddles at the bottom of the door, a filling sound that seems to go on and on, and heavy foam in the tub.

Likely causes (most → least common)

  1. Wrong detergent or too much of it (foam)Most common

    Samsung UK lists strong detergent foam as a typical OC symptom. Hand dish soap, a double dose or spilled rinse aid creates suds that the level sensor reads as extra water.

  2. Clogged filter or debris in the sumpCommon

    Samsung Canada's fix for OC is to inspect and clean the filter and sump. Food debris that blocks drainage leaves water standing in the tub.

  3. Kinked, pinched or crushed drain hoseCommon (especially after installation)

    Samsung says the most common drain problem right after installation is the dishwasher sitting on its own drain hose and pinching it shut.

  4. No air gap or high loop on the drain hoseCommon

    Without an air gap or a high loop (part of the hose higher than its connection at the sink), dirty water can flow back from the sink into the dishwasher and push the level up.

  5. Blocked sink drain or garbage disposalCommon

    If the sink or disposal is clogged, the dishwasher cannot get rid of its water. On a newly installed disposal, the knockout plug (disposal cap) may still be in place.

  6. Standing water left in the base pan after an earlier overflowOccasional

    Samsung UK says water in the base pan from an overfill or small leak must be removed before the dishwasher is restarted.

  7. Water inlet valve not closing, faulty level sensor or control faultLess common

    If OC returns with clean filters, correct detergent and a clear drain, a component may be at fault. This needs Samsung service or a qualified technician.

How to fix it, step by step

  1. Stop the cycle and shut off the water if it is overflowing

    Turn the dishwasher off. If water is coming out of the door or pooling on the floor, close the water supply valve (usually under the sink) — Samsung UK specifically says to turn off the water supply when overflow occurs. Mop up any water around the unit.

    Easy⏱ 5 min🔧 Towels
  2. Check for foam and the detergent you used

    Open the door and look for suds. If you used hand dish soap, overdosed detergent or spilled rinse aid, scoop out the foam, wipe the tub and dispenser area, and next time use only a normal dose of proper dishwasher detergent. Foam is the most common reason for OC that doesn't involve any fault.

    Easy⏱ 10–20 min🔧 Cup or sponge, Towels
  3. Clean the filter and the sump

    Remove the lower rack, then take out the filter as described in your user manual. Rinse it under the tap, clear food scraps and broken glass from the sump below, and put every part back exactly as it came out. Samsung warns that missing or incorrectly refitted filter parts can themselves cause drain errors.

    Easy⏱ 10–15 min🔧 Soft brush, Gloves
  4. Check the sink drain and garbage disposal

    Run the sink tap for about 30 seconds. If the sink does not drain, the problem is the home's plumbing rather than the dishwasher — call a plumber. If you have a garbage disposal, run it to clear it, and if it was recently installed make sure the knockout plug at the dishwasher inlet has been removed.

    Easy⏱ 5–10 min🔧 Flashlight
  5. Inspect the drain hose

    Look under the sink and, if you can, behind the toe-kick. Make sure the dishwasher is not standing on the hose and that the hose is not kinked, flattened or damaged. Check that it either runs through an air gap or has a high loop above its connection to the sink, according to your local regulations and the installation manual.

    Moderate⏱ 15–30 min🔧 Flashlight, Screwdriver (toe-kick panel, model-dependent)
  6. Remove water from the base, then restart

    If water got into the base pan, let it dry out before restarting. Then cut power at the breaker for about five minutes, restore it and run a short or Normal cycle with an empty, correctly dosed dishwasher. Stay nearby and watch for continuous filling or water at the door.

    Easy⏱ 5 min + drying time🔧 No tools

When to call a professional

  • The dishwasher keeps filling with water even while switched off or after the cycle ends — close the water valve and book service; the inlet valve may be stuck open.
  • OC returns with no foam, a clean filter, a clear sink drain and a correctly routed drain hose.
  • The drain hose is damaged and cannot be straightened — Samsung recommends contacting its service.
  • OC alternates with the LC leak code, or you see water coming from inside the cabinet rather than the door.
  • The sink itself will not drain — that is a job for a plumber, not a dishwasher repair.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Filter assembly

Replace if a filter part is cracked, missing or will not lock in place correctly.

Fit: Model-specific. Check the parts list for your exact Samsung model number (label on the inner door edge).

No price shown — prices are only listed when verified on a retailer page.

Drain hose

Replace if the hose is split, crushed or permanently kinked.

Fit: Model-specific length and connectors.

No price shown — prices are only listed when verified on a retailer page.

Water inlet valve

Only if a technician confirms it does not close and the dishwasher keeps filling.

Fit: Model-specific. Diagnosis needs electrical testing — best left to a pro.

No price shown — prices are only listed when verified on a retailer page.

Related codes

All Samsung dishwasher error codes · Every code A–Z

FAQ

Are OC, 0C and oE the same code on a Samsung dishwasher?

Yes. Samsung lists OC, 0C and oE together as the over-level water error. The way it looks depends on your model's display.

Is OC a drain problem or a filling problem?

Usually a drain or foam problem. Samsung groups OC with the 5C drain error and points to the same checks: sink drain, drain hose, filter and sump. If the machine keeps filling even when off, that points to a stuck inlet valve instead — call for service.

Can the wrong detergent cause OC?

Yes. Samsung UK lists heavy foam from the wrong detergent or too much detergent as a typical OC symptom. Use only dishwasher detergent in the recommended dose.

How do I clear the OC code?

Fix the cause, remove any water from the base, then switch off at the breaker for about five minutes and run a cycle. Samsung advises against just resetting without troubleshooting, because the code will come back.

My dishwasher has no display. How does it show OC?

Models without a display use blinking light combinations instead. Samsung UK gives Heavy and Auto blinking together as one example of a drain or overflow error; check your user manual for your model's pattern.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.