Samsung · Dishwasher
Samsung Dishwasher 5C Error Code: Not Draining — Causes & Fixes
Also shown as: 5E, SC, SE
5C (or 5E) means your Samsung dishwasher can't drain. Samsung's checklist: clear the sink drain and garbage disposal (including the knockout cap on a new disposal), make sure the dishwasher isn't sitting on its own drain hose, check for a high loop or air gap, then clean and correctly refit the filter.
What 5C means
The dishwasher tried to pump water out but could not empty the tub. Samsung shows this as 5C on newer displays and 5E, SC or SE on others. Samsung US points out that the cause is often the sink drain or the drain-hose installation rather than the dishwasher itself. Samsung UK also lists a frozen, bent or clogged drain hose, broken glass or other debris in the drain pump, a clogged filter, and, less often, a pressure switch or control board fault.
Likely causes (most → least common)
- Blocked sink drain or garbage disposalMost common
Samsung US says the sink's drain can be the real cause. Run water in the sink for about 30 seconds. If the sink doesn't drain either, it's a plumbing problem, not the dishwasher.
- Knockout cap left in a new garbage disposalVery common after installation
If the dishwasher or disposal was recently installed, Samsung says to make sure the disposal cap (knockout plug) was removed, because it blocks the drain.
- Dishwasher sitting on its own drain hose, or hose kinkedVery common after installation
Samsung US calls a dishwasher pinching its own drain hose the most common drain problem right after installation. Kinks and bends from recent work under the sink are next.
- No high loop or air gapCommon
Without an air gap or a high loop (part of the hose above its sink connection), water can flow back into the dishwasher. Samsung says to follow local regulations.
- Clogged or wrongly refitted filterCommon
Food soil in the filter blocks draining. Samsung warns that missing or incorrectly inserted filter parts can also cause drain errors.
- Frozen drain hose, debris in the pump, or a faulty pressure switch or control boardLess common
Samsung UK lists frozen hoses and broken plate fragments in the pump impeller, plus sensor and control board faults that need service.
How to fix it, step by step
Test the sink drain
Run water in the sink the dishwasher drains into for about 30 seconds. If the sink backs up, clear the sink drain or call a plumber first.
Check the garbage disposal
Make sure the disposal is clear (run it with water). If it is new, check that the knockout plug inside the dishwasher inlet was removed. If it wasn't, the disposal has to come off to knock it out.
Inspect the drain hose
Turn off power to the dishwasher. Under the sink, follow the drain hose and straighten any kinks. Make sure there is an air gap or a high loop above the sink connection. If the dishwasher was just installed, check it isn't standing on its own hose. That may mean sliding it out.
Clean and refit the filter
Remove the bottom rack and take out the filter assembly as your manual describes. Rinse it under running water and clear food from the sump area. Watch for sharp debris such as broken glass. Refit every part exactly as the manual shows, because Samsung warns that missing or wrongly inserted parts can cause drain errors.
Check for frozen lines
If the dishwasher is against an outside wall in freezing weather, let the cabinet warm up with the door under the sink open. Samsung notes that frozen lines aren't covered by warranty service.
Run a test cycle
Restore power and run a rinse or short cycle. If it still won't drain, request service. The pump, pressure switch or control board may be at fault.
When to call a professional
- The sink drains fine, the hose is clear and the filter is clean, but the dishwasher still won't drain.
- You hear the drain pump hum without water moving. There may be debris in the pump or a failed pump.
- The drain hose is damaged and can't be straightened. Samsung recommends service.
- The sink itself won't drain. Call a plumber, not a dishwasher technician.
Parts that may be involved
Always match the part to your exact model number (rating label) before ordering.
Drain hose (model-specific)
If the hose is crushed or split and can't be straightened.
Fit: Match the model's specified length. Don't add improvised extensions.
No price shown — prices are only listed when verified on a retailer page.
Filter assembly
If a filter part is cracked or lost and can't be refitted correctly.
Fit: Model-specific. Check the parts list for your exact model.
No price shown — prices are only listed when verified on a retailer page.
Drain pump
Only if it has failed. That is usually confirmed by a technician.
Fit: Model-specific.
No price shown — prices are only listed when verified on a retailer page.
Related codes
Same problem on other brands
FAQ
Is 5C the same as 5E on a Samsung dishwasher?
Yes. Samsung lists 5C, SC, 5E and SE as the same drain error. The display style just varies by model.
How do I reset a Samsung dishwasher 5C code?
Fix the drain problem first, then turn the dishwasher off and on and run a short cycle. If water still stays in the tub, the code will come back.
My Samsung dishwasher shows 5C right after installation. Why?
Samsung says the most common reason right after installation is that the dishwasher is sitting on its own drain hose. A disposal knockout plug that wasn't removed is the other classic cause.
Does Samsung's warranty cover a frozen drain line?
Samsung US says frozen water or drain lines are not covered under warranty service. Thaw them first and only book service if you know the lines aren't frozen.
Sources
This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.
- Samsung dishwasher is not draining — Samsung US (last checked 2026-11-18)
- 5C/5E, 4C/4E, and LC/LE information codes on my dishwasher — Samsung UK (last checked 2026-11-18)
- Samsung dishwasher is displaying an error code — Samsung US (last checked 2026-11-18)