Easily check your error code

Samsung · Dryer

Samsung Dryer 9C1 Error Code: Voltage / Power Supply Problem — Causes & Fixes (Electric Dryers)

Also shown as: 9E1, 9E, 2E

9C1

9C1 (also 9E1, 9E or 2E) means your Samsung dryer sees abnormal voltage on its power supply. Check the breakers, extension cords, the outlet and the power cord first — the dryer itself is often fine.

Easy⏱ 10–30 minUpdated 2026-11-20

What 9C1 means

Samsung lists 9C1 together with 9E, 2E and 9E1 as voltage errors: the dryer has detected that the voltage it is getting is outside the range it expects. Samsung US and Canada point first at the supply side — a shared circuit, an extension cord, an incorrectly installed power cord on electric models, or a dryer used outside the country it was built for. Samsung UK and Australia group 9C1/9E1 with 9C2/9E2 and describe them as 'the electronic control needs to be checked' after confirming power is supplied and the plug is in. There is also one harmless case: on stacked pairs with a multi-control kit, the washer can report a dryer 9C1 if you try to operate the dryer within 5 seconds of switching the washer on. This guide covers electric dryers only; on a gas dryer, contact Samsung or a qualified technician.

Likely causes (most → least common)

  1. Multi-control kit timing on a stacked washer/dryer (not a real fault)Common on stacked sets with a multi-control kit

    Samsung US says the washer may show a dryer 9C1 if you try to control the dryer less than 5 seconds after turning the washer on. Samsung offers a software update for this through the SmartThings app.

  2. Half-tripped or tripped breakerCommon

    Electric dryers run on a two-pole circuit (30 A on both sides of the line in the US and Canada). Samsung notes that one side can trip while the other stays on, which leaves the dryer with only part of its supply.

  3. Extension cord, adapter or shared circuitCommon

    Samsung's first check for 9C1 is that the dryer is on its own circuit and not plugged in through an extension cord. Extension cords and adapters cause voltage drop under load.

  4. Power cord installed incorrectly, loose or damagedCommon after a new installation or move

    US electric models ship without a cord, so it is fitted on site. Samsung asks you to confirm the cord is installed properly and warns not to reuse an old dryer's cord. Loose terminals, burn marks or a worn plug can all cause unstable voltage.

  5. Low or wrong supply voltage at the outletOccasional

    Samsung's manual says to confirm 240 V between L1 and L2 at the receptacle before installation. Some US models are rated for 120/208 V instead of 120/240 V — the requirement is on the data label behind the door.

  6. Dryer used outside the country it was sold inOccasional (imported or relocated dryers)

    Samsung says 9C1 can appear when a model is taken abroad, because power grids and regulations differ between countries.

  7. Electronic control (main board) faultLess common

    If the supply checks out and 9C1 keeps returning, Samsung UK and Australia say the electronic control needs to be checked by Samsung service.

How to fix it, step by step

  1. Rule out the multi-control kit timing issue

    If your dryer is stacked on a Samsung washer and controlled from it, switch the washer on and wait at least 5 seconds before selecting anything for the dryer. If the code only shows on the washer's display in this situation, add the dryer to the SmartThings app and install the available software update. Samsung says the update takes about 20 minutes and the dryer will not respond while it installs.

    Easy⏱ 5–25 min🔧 Smartphone with the SmartThings app
  2. Reset both breakers

    At your electrical panel, switch the dryer breaker fully OFF, wait 30 seconds, then switch it back ON. Samsung recommends this because a half-tripped two-pole breaker can look as if it is still on. In the UK, Australia and other 230 V regions, check that the socket is switched on and the RCD/breaker has not tripped. Then restart the cycle and see whether 9C1 returns.

    Easy⏱ 5 min🔧 No tools
  3. Remove extension cords and adapters

    Plug the dryer directly into its own wall outlet. Samsung says the dryer should be on its own circuit and not use an extension cord. If you are using a plug adapter or a power strip, remove it. If the dryer shares a circuit with other big loads, that circuit needs looking at by an electrician.

    Easy⏱ 5 min🔧 No tools
  4. Inspect the plug, cord and outlet (power off)

    Turn the breaker off and unplug the dryer. Look at the plug, the cord along its length and the wall outlet for scorch marks, melted plastic, cracks or loose prongs. Samsung's power troubleshooting says to stop and contact an electrician if you see burn marks or damage. Do not plug a damaged cord back in.

    Easy⏱ 5–10 min🔧 Flashlight
  5. Check the rating label and the cord type

    Open the dryer door and read the data label: it states whether your model needs 120/240 V or 120/208 V. In the US, the cord must match the outlet (3-prong in many older homes, 4-prong NEMA 14-30R in newer ones) and be rated for 30 A. Samsung says not to reuse a cord from an old dryer. If the cord was fitted recently, ask the installer to check the connections at the terminal block — that is where an incorrect installation shows up.

    Easy⏱ 5–10 min🔧 Flashlight
  6. Check whether the dryer was made for your country

    If the dryer was bought abroad or moved from another country, compare the voltage and frequency on its data label with your local supply. Samsung says this mismatch alone can cause 9C1. Using a dryer on the wrong supply is not something to fix with an adapter or converter — contact Samsung.

    Easy⏱ 5 min🔧 No tools
  7. Have the supply voltage measured, then book service

    If 9C1 keeps coming back, have a licensed electrician measure the voltage at the outlet under load (Samsung's manual specifies 240 V between L1 and L2 for US electric models). If the supply is correct, the dryer's electronic control needs checking — request service from Samsung.

    Hard⏱ Electrician / service visit🔧 Licensed electrician

When to call a professional

  • You see burn marks, melted plastic or damage on the plug, cord or outlet, or you smell burning — call a licensed electrician before using the dryer again.
  • The breaker trips again as soon as you reset it, or trips with the dryer unplugged — that is a house wiring problem for an electrician.
  • The power cord needs to be replaced or re-connected at the dryer's terminal block and you are not trained to do it — use a qualified installer or electrician.
  • The supply voltage has to be measured at the outlet — that means working near live 240 V terminals, a job for an electrician.
  • 9C1 returns even though the supply is confirmed correct — Samsung says to request service; the electronic control needs to be checked.
  • Your dryer is a gas model — do not do any gas or burner work yourself; contact Samsung or a qualified technician.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Dryer power cord (3- or 4-wire, 30 A)

Replaces a damaged, worn or reused cord. US electric Samsung dryers ship without a cord.

Fit: Must match your outlet (3-prong or 4-prong NEMA 14-30R), be rated at least 120/240 V and 30 A and be listed for dryers. Canadian models come with a cord attached.

No price shown — prices are only listed when verified on a retailer page.

Strain relief for the dryer cord

Holds the cord securely at the cabinet so the terminals cannot work loose.

Fit: UL-listed strain relief for dryer cords; often included with a cord kit.

No price shown — prices are only listed when verified on a retailer page.

Main control board (electronic control)

Only if Samsung service or a technician confirms the control is at fault after the supply has been checked.

Fit: Model-specific. Diagnosis needs electrical testing — leave it to a pro.

No price shown — prices are only listed when verified on a retailer page.

Related codes

All Samsung dryer error codes · Every code A–Z

FAQ

Are 9C1, 9E1, 9E and 2E the same error?

Yes. Samsung US and Canada list 9C1, 9E, 2E and 9E1 together as voltage errors. Which one you see depends on the model and its display.

Is 9C1 a problem with the dryer or with my house?

Usually with the supply: a half-tripped breaker, an extension cord, a shared circuit or a badly fitted cord. Samsung only points to the dryer's electronic control once the power supply has been confirmed.

Why does my washer show a 9C1 for the dryer?

On stacked Samsung pairs with a multi-control kit, the washer can report a dryer 9C1 if you operate the dryer within 5 seconds of turning the washer on. Wait a few seconds, and install the software update Samsung offers through the SmartThings app.

How do I reset a 9C1 code?

Switch the dryer's breaker fully off for 30 seconds, switch it back on and restart the cycle. If the code comes back, the cause is still there — work through the supply checks above.

Can I run the dryer while it shows 9C1?

Not reliably — the dryer is reacting to an abnormal supply. If there are signs of burning or damage, leave it unplugged until an electrician has checked it.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.